Dryer Repair Burleson — Wet Clothes, Second Cycle Again?
Wet clothes after a full cycle in Burleson usually trace to heat or airflow, not a dead dryer. Clean the vent first, then work the ladder. Burleson Refrigerator Repair connects you with independent local pros for dryer repairs too. Call (817) 803-8995 and say whether it tumbles and whether it heats.
Clean the vent first. Really, check it first.
Here is the honest advice that costs nothing. A clogged vent causes more no-heat calls than any failed part.
Lint builds in the screen, the duct, and the outside flap. Hot air cannot leave, so the dryer overheats inside. Clothes stay damp, cycles run long, and safety switches start tripping.
Pull the lint screen and wash it if fabric softener film coats it. Check the outside vent flap while the dryer runs. It should open wide with strong warm airflow.
Then look behind the machine. A crushed flexible duct chokes airflow as surely as a lint plug does.
If airflow is weak outside, clean the full vent run or book it done before booking a part. Replacing a heating element behind a clogged vent just burns out the new element.
Lint is also a fire risk, not just a performance problem. A vent you cannot remember cleaning is overdue, whatever the dryer is doing.
My dryer heats but takes two cycles. Is that the element?
Usually not. An element either heats or it does not. Two-cycle drying with real heat points at airflow: screen, duct, or outside flap. Clean the vent path first. If drying stays slow with strong airflow, then book a diagnosis.
No heat at all? Work the ladder in order.
On an electric dryer, no heat follows a short ladder. Pros test it in this order, cheapest and most common first.
- Thermal fuse: a one-time safety switch. It blows when the dryer overheats, often because the vent was clogged. A blown fuse means no heat until it is replaced and the cause is fixed.
- Cycling thermostat: it switches the element on and off to hold temperature. A failed one can cut heat early or kill it entirely.
- Heating element: the coil itself. It can break or short after years of cycles. Element failure is real, but it is third on the ladder, not first.
Swapping parts in the wrong order wastes money. A new fuse behind a clogged vent blows again. A new element behind a bad thermostat still misbehaves.
Testing these parts needs a meter and the cabinet open near live wiring. That is pro work for most owners, and the diagnosis is quick.
What about gas dryers? Those are pro-only, full stop.
Gas dryers add a gas valve, an igniter, and flame sensors to the same drum and airflow. The no-heat ladder is different, and so is the risk.
Do not open a gas dryer, test its valve, or bypass a sensor yourself. Gas and ignition faults belong to a licensed pro only. That line does not bend.
Signs of a gas-side fault include no heat with a normal tumble, a clicking igniter with no flame, or any gas smell at all.
If you smell gas, stop the machine, leave the area, and call your gas utility from outside. Do not book a repair call as the first step.
On the call to (817) 803-8995, say the dryer is gas up front. You get matched with a pro who is set up for gas work, not one who arrives and declines it.
Can a gas dryer be converted or swapped for electric easily?
Rarely easily. It needs the right circuit, outlet, and vent plan. Most owners repair the gas unit or replace it like for like. Your pro can price the repair so you can compare it with a new gas dryer honestly.
Squealing, thumping or not tumbling: the moving parts
Noise tells its own story. A high squeal on startup often points at the belt or the idler pulley that tensions it.
A rhythmic thump can be a flattened drum roller or a load sitting wrong. Rollers wear flat spots over years, and the thump keeps time with the drum.
No tumble with a humming motor points at a snapped belt first. The motor runs, the drum does not turn, and heat should shut off for safety.
No tumble and no sound at all is different. Check the door switch and the breaker before assuming the motor died.
Bearings and rollers sit mid-range as repairs go. Belts sit lower. Motors sit higher, and on an old dryer a motor quote should trigger the repair-or-replace talk.
| Symptom | First check | Likely pro fix |
|---|---|---|
| No heat, electric | Vent airflow outside | Thermal fuse, thermostat, then element |
| No heat, gas | Nothing inside the cabinet | Licensed pro only: igniter or valve work |
| Heats, dries slowly | Lint screen, duct, outside flap | Full vent clean before any part |
| Squeals or thumps | Empty-drum test spin by ear | Belt, idler pulley, or drum rollers |
| Will not tumble | Door switch and breaker | Belt first, motor last |
What will it cost, and when is a new dryer smarter?
Dryer prices split by part, like washer prices do. Honest ranges beat a fixed phone quote, and anyone giving one sight unseen is guessing.
Across the market, a diagnostic visit typically costs $50–$100. Your matched pro confirms the exact repair range in writing before any part is ordered or fitted.
Belts, fuses, and thermostats sit at the low end. Elements sit in the middle. Motors and control boards sit at the top.
Run the rule before a big quote. Repair if the dryer is under about 10 years old and the quote is under 50% of replacement cost. The fridge version of that math is on the refrigerator repair cost guide.
If the washer is the same age and also limping, say so. The pair shares a laundry room and a history. See washer repair for its failure list.
Rentals, holidays and the rest of the house
A dead dryer hits rentals and holiday houses harder than owners expect. Guests and tenants judge a place by hot showers and dry towels.
Landlords in Burleson can route approvals through the landlords and property managers page. The tenant reports, the owner approves, the pro attends. No one waits at the house all day.
Timing matters in December too. BTX-MAS week and Christmas guests stack laundry loads back to back. A dryer limping in November rarely survives the holidays.
The holiday refrigerator prep guide covers the fridge side of that same late-October check. Do the dryer vent on the same weekend.
Browse the services hub for the full network list. Most dryer repair Burleson calls start with three words: tumble, heat, and noise. Call (817) 803-8995 and lead with those. They start the diagnosis before the pro even arrives.
Frequently asked questions
How much does dryer repair cost in Burleson?
It depends on the part. Belts, thermal fuses, and thermostats sit at the low end. Heating elements sit in the middle. Motors and boards sit at the top. Diagnostic visits typically run $50–$100 across the market. Your pro gives a written price range after diagnosis, before work starts.
Why does my dryer run but not heat?
Work the ladder. First, airflow: a clogged vent overheats the dryer and blows the thermal fuse. Next, the cycling thermostat. Last, the element itself. On a gas dryer, the igniter and valve join the list, and those are licensed pro work only. Guessing at parts usually costs more than diagnosing.
How often should I clean my dryer vent?
Clean the lint screen after every load. Check the outside flap monthly for strong airflow. Have the full duct run cleaned when drying slows, when the laundry room feels humid during a cycle, or at least every year or two in a busy family house. Slow drying is the vent asking first.
Is a squealing dryer safe to keep using?
A short finish to a load is usually fine. Weeks of it is not. Squeals usually mean a belt or idler pulley wearing out, and a snapped belt can leave the drum stalled mid-cycle. Book it while it still tumbles. The repair is smaller before the belt lets go completely.
Should I repair a 12-year-old dryer with a bad motor?
Run the rule. Repair if the dryer is under about 10 years old and the quote is under 50% of replacement cost. A motor is a top-end repair, so a 12-year-old dryer often fails both tests. Ask for the motor quote and a replacement comparison in writing, then decide with both numbers in hand.
Fridge trouble in Burleson?
Call (817) 803-8995 for dryer repair Burleson homeowners can approve in writing first. You get matched with an independent local pro, and no work starts without your OK.